收藏本站
Si10xx-DK
10.2. Target Board Power Options and Current Measurement
The Si10xx Target Board supports three power options, selectable by the three-way header (J10/J11). The power
options vary based on the configuration (one-cell or two-cell mode) selected by SW4. Power to the MCU may be
switched on/off using the power switch (SW5). Important Note: The power switch (SW5) must be in the OFF
position prior to switching between one-cell and two-cell mode using SW4. The power options are described
in the paragraphs below.
10.2.1. Wall Power
When the J10/J11 three-way header is set to WALL_PWR, the Si10xx Motherboard may be powered from the
following power sources:
?
?
?
9 VDC power using the ac to dc power adapter (P2)
5 VDC USB VBUS power from PC via the USB Debug Adapter (J9)
5 VDC USB VBUS power from PC via the CP2103 USB connector (P3)
All the three power sources are ORed together using reverse-biased diodes (D1, D2, D3), eliminating the need for
headers to choose between the sources. The target board will operate as long as any one of the power sources is
present. The ORed power is regulated to a 3.3 V dc voltage using a LDO regulator (U2). The output of the regulator
powers the +3 VD net on the target board.
If SW4 is configured to select two-cell mode, the VBAT supply net on the target board is powered directly from the
+3 VD net. If SW4 is configured to select one-cell mode, the VBAT supply net is powered directly from the +1 VD.
This power supply net takes +3 VD and passes it through a 1.65 V LDO. The LDO’s output voltage is variable and
can be set by changing the value of resistor R32.
J11
COIN_CELL
AAA_BAT
VBAT
WALL_PWR
10.2.2. AAA Battery
When the J10/J11 three-way header is set to AAA_BAT, the Si10xx Target Board may be powered from a single
AAA battery inserted in BT1 or from the series combination of the AAA batteries inserted in BT1 and BT2. A single
battery is selected when SW4 is configured to one-cell mode. The two AAA batteries configured in series to provide
a voltage of ~3 V are selected when SW4 is configured to two-cell mode.
J11
COIN_CELL
AAA_BAT
VBAT
WALL_PWR
10.2.3. Coin Cell Battery
When the J10/J11 three-way header is set to COIN_CELL, the Si10xx Target Board may be powered from a single
1.5 V Alkaline (A76) or Silver Oxide (357) button cell inserted in BT4 or from a single 3 V Lithium (CR2032) coin
cell inserted in BT3. The button cell (BT4) is selected when SW4 is configured to one-cell mode, and the coin cell
(BT3) is selected when SW4 is configured to two-cell mode.
J11
COIN_CELL
AAA_BAT
VBAT
WALL_PWR
10.2.4. Measuring Current
The header (J17) and terminal block (H2) provide a way to measure the total supply current flowing from the power
supply source to the MCU. The measured current does not include any current from the VBAT LED (DS2), the
address latch (U4) or the quiescent current from the power supply; however, it does include the current used by
any LEDs powered from the VDD/DC+ supply net or sourced through a GPIO pin. See the target board schematic
in Figure 11 through Figure 13 for additional information.
Rev. 0.1
15
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SI1021R-T1-GE3 MOSFET P-CH 60V 190MA SC-75A
SI1022R-T1-GE3 MOSFET N-CH 60V 330MA SC-75A
SI1024X-T1-GE3 MOSFET DL N-CH 20V 485MA SC89-6
SI1025X-T1-GE3 MOSFET P-CH 60V 190MA SC-89
SI1029X-T1-GE3 MOSFET N/P-CH 60V SC89-6
SI1031X-T1-E3 MOSFET P-CH 20V 155MA SC-75A
SI1033X-T1-GE3 MOSFET 2P-CH 20V 145MA SC89
SI1037X-T1-E3 MOSFET P-CH 20V 770MA SC-75A
相关代理商/技术参数
SI1011 制造商:SILABS 制造商全称:SILABS 功能描述:Ultra Low Power, 16/8 kB, 12/10-Bit ADC MCU with Integrated 240-960 MHz EZRadioPRO Transceiver
Si1011-A-GM 功能描述:射频微控制器 - MCU 8kB 768B RAM programmable XCVR RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:Si100x 数据总线宽度:8 bit 最大时钟频率:24 MHz 程序存储器大小:64 KB 数据 RAM 大小:4 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LGA-42 安装风格:SMD/SMT 封装:Tube
SI1011-A-GMR 功能描述:射频微控制器 - MCU 8kB 768B RAM +20 dBm programmable XCVR RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:Si100x 数据总线宽度:8 bit 最大时钟频率:24 MHz 程序存储器大小:64 KB 数据 RAM 大小:4 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LGA-42 安装风格:SMD/SMT 封装:Tube
Si1011-C-GM2 制造商:Silicon Laboratories Inc 功能描述:8KB 768B RAM 20DB XCVR QFN42 制造商:Silicon Laboratories Inc 功能描述:RF Microcontrollers - MCU 8kB, 768B RAM +20 dBm
SI1011-C-GM2R 制造商:Silicon Laboratories Inc 功能描述:8KB, 768B RAM, +20 DBM, PROGRAMMABLE XCVR - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC MCU 8KB FLASH EZ PRO 42LGA 制造商:Silicon Laboratories Inc 功能描述:RF Microcontrollers - MCU 8kB 768B RAM +20 dBm programmable XCVR
SI1012 制造商:SILABS 制造商全称:SILABS 功能描述:Ultra Low Power, 16/8 kB, 12/10-Bit ADC MCU with Integrated 240-960 MHz EZRadioPRO Transceiver
Si1012-A-GM 功能描述:射频微控制器 - MCU 16kB 768B RAM programmable XCVR RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:Si100x 数据总线宽度:8 bit 最大时钟频率:24 MHz 程序存储器大小:64 KB 数据 RAM 大小:4 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LGA-42 安装风格:SMD/SMT 封装:Tube
SI1012-A-GMR 功能描述:射频微控制器 - MCU 16kB 768B RAM +13 dBm Prog XCVR RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:Si100x 数据总线宽度:8 bit 最大时钟频率:24 MHz 程序存储器大小:64 KB 数据 RAM 大小:4 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LGA-42 安装风格:SMD/SMT 封装:Tube